List of Topics

SfC Home > Physical Science > Physics > Friction >


Key words: Listing friction, coefficient, sliding, hard, greased materials, Physical Science Physics, static, kinetic, surface roughness, clean, lubricated, scientific measurements, engineering tables, scientific method, Ron Kurtus, School for Champions. Copyright © Restrictions

Coefficient of Friction Values for Greased Surfaces

by Ron Kurtus (revised 25 May 2014)

Engineering laboratories have measured the coefficient of friction for a number of materials that are lubricated by grease and have tabulated the results. These coefficient of friction values apply only to sliding hard surfaces against each other. Since various experimental parameters such as the type of grease are not listed, considerations should be made in using these tabulated values because they may not directly relate to your application.

Questions you may have include:

This lesson will answer those questions. Useful tool: Units Conversion


The information available on the various coefficients of friction provide a starting point on the subject, but unfortunately the values lack a good scientific basis.

Condition of materials

Effective scientific measurements typically state the exact condition of materials and that of the surrounding environment. Although lubrication with grease may negate the surface roughness factor of the materials, it is still good scientific practice to document the roughness. Another needed factor is the physical condition of the materials.

Test setup

Describing the test setup is important in order to allow others to duplicate and verify the measurements. With friction, the normal force can be a factor in the case of hard materials that may deform slightly under high pressure. That value should be part of the test description.

Testing environment

It is also important to state the testing environment. Although it is unlikely measurements were made under extreme temperature and humidity conditions that affect the coefficient, at the very least those items should be noted.

Greased materials

The static and kinetic coefficients of friction were measured for a variety of materials where "grease" was used as a lubricant. A major problem in using these readings is that we do not know what type of grease was used. Lubrication can vary considerably, depending on the material.

Another factor is the thickness of the lubricating lever of grease. It is assumed a thin coat of grease it used. A real thick coat of grease could greatly change the coefficient values.


The values in the following table show that measurements on most materials seemed to be either static or kinetic. The reference source of the values listed does not indicate why both types of friction were not measured.

You can use these values for the coefficient as a guide, but it is best to perform some tests and measurements in your specific application to get good values.

Coefficient of Sliding Friction (greased surfaces)

Material 1

Material 2



Aluminum Aluminum 0.3 -
Bronze Steel 0.16 -
Cadmium Cadmium 0.05 -
Cast Iron Cast Iron - 0.07
Cast Iron Oak - 0.08
Chromium Chromium 0.03 -
Copper Copper 0.08 -
Copper Mild Steel - 0.18
Diamond Diamond 0.05 - 0.1 -
Diamond Metal 0.1 -
Glass Glass 0.1 - 0.6 0.09 - 0.12
Glass Metal 0.2 - 0.3 -
Graphite Graphite 0.1 -
Graphite Steel 0.1 -
Hard Carbon Hard Carbon 0.12 - 0.14 -
Hard Carbon Steel 0.11 - 0.14 -
Iron Iron 0.15 - 0.2 -
Leather Metal (clean) 0.2 -
Magnesium Magnesium 0.8 -
Nickel Nickel 0.28 0.12
Nickel Mild Steel - 0.18
Oak Oak (cross grain) - 0.07
Platinum Platinum 0.25 -
Plexiglas Plexiglas 0.8 -
Plexiglas Steel 0.4 - 0.5 -
Polystyrene Polystyrene 0.5 -
Polystyrene Steel 0.3 - 0.35 -
Polythene Steel 0.2 -
Sapphire Sapphire 0.2 -
Silver Silver 0.55 -
Sintered Bronze Steel 0.13 -
Steel Brass 0.19 -
Steel (mild) Cast Iron 0.18 0.13
Steel Cast Iron 0.12 -
Steel Copper Lead Alloy 0.16 0.15
Steel (hard) Graphite 0.09 -
Steel Graphite 0.1 -
Steel (mild) Lead 0.5 0.3
Steel (mild) Phos. Bros - 0.17
Steel (hard) Polythene 0.2 -
Steel (hard) Polystyrene 0.3 - 0.35 -
Steel (mild) Steel (mild) - 0.09 - 0.19
Steel (hard) Steel (hard) 0.05 - 0.11 0.03 - 0.12
Teflon Steel 0.04 0.04
Teflon Teflon 0.04 0.04
Tungsten Carbide Tungsten Carbide 0.12 -
Tungsten Carbide Steel 0.08 - 0.2 -
Zinc Zinc 0.04 -


Coefficient of friction have been measured for a number of hard, greased materials. A problem occurs with the values in the table concerning the type of grease used. Considerations should be made in using this tabulated material, since it may not directly relate to your application.

Be excellent in your work

Resources and references

Ron Kurtus' Credentials


Engineer's Handbook - Coefficient of Friction

RoyMech (UK) - Friction Factors

Friction Resources - Extensive list


The following books are available from


Complete Idiot's Guide To Physics by Johnnie T. Dennis; Alpha (2003) $18.95

What Is Friction? (Ages 4-8) by Lisa Trumbauer; Children's Press (CT) (2004) $4.95


Friction and Lubrication in Mechanical Design (Mechanical Engineering Series) by Ali Seireg; Marcel Dekker Pub. (1998) $199.95

Physics of Sliding Friction (NATO Science Series E:) by B.N. Persson, E. Tosatti; Springer Pub. (1996) $358.00

Questions and comments

Do you have any questions, comments, or opinions on this subject? If so, send an email with your feedback. I will try to get back to you as soon as possible.


Click on a button to bookmark or share this page through Twitter, Facebook, email, or other services:


Students and researchers

The Web address of this page is:

Please include it as a link on your website or as a reference in your report, document, or thesis.

Where are you now?

School for Champions

Friction topics

Coefficient of Friction Values for Greased Surfaces

Friction topics


Coefficient of friction

Sliding friction

Rolling friction

Fluid friction

Let's make the world a better place

Be the best that you can be.

Use your knowledge and skills to help others succeed.

Don't be wasteful; protect our environment.

You CAN influence the world.

Live Your Life as a Champion:

Take care of your health

Seek knowledge and gain skills

Do excellent work

Be valuable to others

Have utmost character

Be a Champion!

The School for Champions helps you become the type of person who can be called a Champion.